Solar

489.113 Qualifications for practice; restrictions. — (1) Any person who desires to engage in contracting on a statewide basis shall, as a prerequisite thereto, establish his or her competency and qualifications to be certified pursuant to this part. To establish competency, a person shall pass the appropriate examination approved by the board and certified by the department. If an applicant has received a baccalaureate degree in building construction from an accredited 4-year college, or a related degree as approved by the board by rule, and has a grade point average of 3.0 or higher, such applicant is only required to take and pass the business and finance portion of the examination. Any person who desires to engage in contracting on other than a statewide basis shall, as a prerequisite thereto, be registered pursuant to this part, unless exempted by this part. (2) A person must be certified or registered in order to engage in the business of contracting in this state. However, for purposes of complying with the provisions of this chapter, a subcontractor who is not certified or registered may perform construction work under the supervision of a person who is certified or registered, provided that the work is within the scope of the supervising contractor’s license, the supervising contractor is responsible for the work, and the subcontractor being supervised is not engaged in construction work that would require a license as a contractor under any of the categories listed in s. 489.105 (3)(d)-(o). This subsection does not affect the application of any local construction licensing ordinances. To enforce this subsection: (a) The department shall issue a cease and desist order to prohibit any person from engaging in the business of contracting who does not hold the required certification or registration for the work being performed under this part. For the purpose of enforcing a cease and desist order, the department may file a proceeding in the name of the state seeking issuance of an injunction or a writ of mandamus against any person who violates any provision of such order. (b) A county, municipality, or local licensing board created by special act may issue a cease and desist order to prohibit any person from engaging in the business of contracting who does not hold the required certification or registration for the work being performed under this part. (3) A contractor shall subcontract all electrical, mechanical, plumbing, roofing, sheet metal, swimming pool, and air-conditioning work, unless such contractor holds a state certificate or registration in the respective trade category, however: (a) A general, building, or residential contractor, except as otherwise provided in this part, shall be responsible for any construction or alteration of a structural component of a building or structure, and any certified general contractor or certified underground utility and excavation contractor may perform clearing and grubbing, grading, excavation, and other site work for any construction project in the state. Any certified building contractor or certified residential contractor may perform clearing and grubbing, grading, excavation, and other site work for any construction project in this state, limited to the lot on which any specific building is located. (b) A general, building, or residential contractor shall not be required to subcontract the installation, or repair made under warranty, of wood shingles, wood shakes, or asphalt or fiberglass shingle roofing materials on a new building of his or her own construction. (c) A general contractor shall not be required to subcontract structural swimming pool work. All other swimming pool work shall be subcontracted to an appropriately licensed certified or registered swimming pool contractor. (d) A general contractor shall not be required to subcontract the construction of a main sanitary sewer collection system, storm collection system, or water distribution system, not including the continuation of utility lines from the mains to the buildings, and may perform any of the services, on public or private property, for which a license as an underground utility and excavation contractor is required under this part. (e) A general contractor shall not be required to subcontract the continuation of utility lines from the mains in mobile home parks, and such continuations are to be considered a part of the main sewer collection and main water distribution systems. (f) A solar contractor shall not be required to subcontract minor, as defined by board rule, electrical, mechanical, plumbing, or roofing work so long as that work is within the scope of the license held by the solar contractor and where such work exclusively pertains to the installation of residential solar energy equipment as defined by rules of the board adopted in conjunction with the Electrical Contracting Licensing Board. (g) No general, building, or residential contractor certified after 1973 shall act as, hold himself or herself out to be, or advertise himself or herself to be a roofing contractor unless he or she is certified or registered as a roofing contractor. (4)(a) When a certificateholder desires to engage in contracting in any area of the state, as a prerequisite therefor, he or she shall be required only to exhibit to the local building official, tax collector, or other person in charge of the issuance of licenses and building permits in the area evidence of holding a current certificate and to pay the fee for the occupational license and building permit required of other persons. (b) Notwithstanding the provisions of paragraph (a), a local construction regulation board may deny, suspend, or revoke the authority of a certified contractor to obtain a building permit or limit such authority to obtaining a permit or permits with specific conditions, if the local construction regulation board has found such contractor, through the public hearing process, to be guilty of fraud or a willful building code violation within the county or municipality that the local construction regulation board represents or if the local construction regulation board has proof that such contractor, through the public hearing process, has been found guilty in another county or municipality within the past 12 months, of fraud or a willful building code violation and finds, after providing notice of an opportunity to be heard to the contractor, that such fraud or violation would have been fraud or a violation if committed in the county or municipality that the local construction board represents. Notification of and information concerning such permit denial shall be submitted to the department within 15 days after the local construction regulation board decides to deny the permit. (c) The local government may also deny issuance of, or may suspend, any outstanding building permit where a contractor fails or refuses to provide proof of public liability and property damage insurance coverage as required by s. 489.115 (5) and workers’ compensation insurance coverage as required by s. 489.114 . (d) It is the policy of the state that the purpose of regulation is to protect the public by attaining compliance with the policies established in law. Fines and other penalties are provided in order to ensure compliance; however, the collection of fines and the imposition of penalties are intended to be secondary to the primary goal of attaining compliance with state laws and local jurisdiction ordinances. It is the intent of the Legislature that a local jurisdiction agency charged with enforcing regulatory laws shall issue a notice of noncompliance as its first response to a minor violation of a regulatory law in any instance in which it is reasonable to assume that the violator was unaware of such a law or unclear as to how to comply with it. A violation of a regulatory law is a “minor violation” if it does not result in economic or physical harm to a person or adversely affect the public health, safety, or welfare or create a significant threat of such harm. A “notice of noncompliance” is a notification by the local jurisdiction agency charged with enforcing the ordinance, which is issued to the licensee that is subject to the ordinance. A notice of noncompliance should not be accompanied with a fine or other disciplinary penalty. It should identify the specific ordinance that is being violated, provide information on how to comply with the ordinance, and specify a reasonable time for the violator to comply with the ordinance. Failure of a licensee to take action correcting the violation within a set period of time would then result in the institution of further disciplinary proceedings. (5) The certificate is not transferable. (6)(a) The board shall, by rule, designate those types of specialty contractors which may be certified under this part. The limit of the scope of work and responsibility of a specialty contractor shall be established by the board by rule. However, a certified specialty contractor category established by board rule exists as a voluntary statewide licensing category and does not create a mandatory licensing requirement. Any mandatory statewide construction contracting licensure requirement may only be established through specific statutory provision. (b) By July 1, 2025, the board shall, by rule, establish certified specialty contractor categories for voluntary licensure for all of the following: 1. Structural aluminum or screen enclosures. 2. Marine seawall work. 3. Marine bulkhead work. 4. Marine dock work. 5. Marine pile driving. 6. Structural masonry. 7. Structural prestressed, precast concrete work. 8. Rooftop solar heating installation. 9. Structural steel. 10. Window and door installation, including garage door installation and hurricane or windstorm protection. 11. Plaster and lath. 12. Structural carpentry. (7) If an eligible applicant fails any contractor’s written examination, except the general and building contractors’ examination, and provides the board with acceptable proof of lack of comprehension of written examinations, the applicant may petition the board to be administered a uniform oral examination, subject to the following conditions: (a) The applicant documents 10 years of experience in the appropriate construction craft. (b) The applicant files written recommendations concerning his or her competency in the appropriate construction craft. (c) The applicant is administered only one oral examination within a period of 1 year. (8) Any public record of the board, when certified by the executive director of the board or the executive director’s representative, may be received as prima facie evidence in any administrative or judicial proceeding. (9)(a) This part does not prevent any contractor from acting as a prime contractor where the majority of the work to be performed under the contract is within the scope of his or her license or from subcontracting to other licensed contractors that remaining work which is part of the project contracted. (b) This part, chapter 471, chapter 481, or any other provision of law does not: 1. Prevent any licensed engineer or architect from contracting directly with a licensed contractor for the preparation of plans, specifications, or a master design manual addressing structural designs used to make an application for building permits. 2. Require a licensed engineer or architect, when preparing drawings, specifications, plans, or master design manuals for use by any licensed contractor, to prepare site-specific drawings, specifications, or plans for the design and construction of single-family and two-family dwellings; swimming pools, spas, or screened enclosures; or any other structure not exceeding 1,200 square feet or one story in height. For the purpose of issuing building permits, local building officials shall accept such drawings, specifications, or plans when submitted by any licensed contractor. Upon good cause shown, local government code enforcement agencies may accept or reject plans prepared by persons licensed under chapter 471, chapter 481, or this chapter. As used in this section, the term “master design manual” means a restrictive design manual intended to be used to design, permit, and construct structures as described in this section. Any such manual must be prepared by a licensed engineer or architect and specifically detail the limits of its use, including, but not limited to, the structure type, size, materials, loading conditions, time limits, applicable codes, and associated criteria. The manual must also detail the required training for the contractor, engineer, or architect using the manual. All master design manuals must be peer reviewed by an independent licensed engineer or architect having no financial interest in the development of the manual or the construction of structures pursuant to the manual. The engineer or architect conducting the peer review must be identified in the manual. (c) Notwithstanding anything in this chapter or any other provision of law, a licensed engineer or architect is not required for the preparation or use of any design guide adopted by the Florida Building Commission as part of the building code pursuant to s. 553.73 . (10) The addition of a new type of contractor or the expansion of the scope of practice of any type of contractor under this part shall not limit the scope of practice of any existing type of contractor under this part unless the Legislature expressly provides such a limitation. (11) Any local act, law, ordinance, or regulation, including, but not limited to, a local building code or building permit requirement, of a county, municipality, or other political subdivision that pertains to hoisting equipment including power-operated cranes, derricks, hoists, elevators, and conveyors used in construction, demolition, or excavation work, that is not already preempted by the Occupational Safety and Health Administration under 29 C.F.R. parts 1910 and 1926, including, but not limited to, local worksite regulation regarding hurricane preparedness or public safety, is prohibited and is preempted to the state. This subsection does not apply to the regulation of elevators under chapter 399 or to airspace height restrictions in chapter 333.

489.105 Definitions. — As used in this part: (1) “Board” means the Construction Industry Licensing Board. (2) “Department” means the Department of Business and Professional Regulation. (3) “Contractor” means the person who is qualified for, and is only responsible for, the project contracted for and means, except as exempted in this part, the person who, for compensation, undertakes to, submits a bid to, or does himself or herself or by others construct, repair, alter, remodel, add to, demolish, subtract from, or improve any building or structure, including related improvements to real estate, for others or for resale to others; and whose job scope is substantially similar to the job scope described in one of the paragraphs of this subsection. For the purposes of regulation under this part, the term “demolish” applies only to demolition of steel tanks more than 50 feet in height; towers more than 50 feet in height; other structures more than 50 feet in height; and all buildings or residences. Contractors are subdivided into two divisions, Division I, consisting of those contractors defined in paragraphs (a)-(c), and Division II, consisting of those contractors defined in paragraphs (d)-(q): (a) “General contractor” means a contractor whose services are unlimited as to the type of work which he or she may do, who may contract for any activity requiring licensure under this part, and who may perform any work requiring licensure under this part, except as otherwise expressly provided in s. 489.113 . (b) “Building contractor” means a contractor whose services are limited to construction of commercial buildings and single-dwelling or multiple-dwelling residential buildings, which do not exceed three stories in height, and accessory use structures in connection therewith or a contractor whose services are limited to remodeling, repair, or improvement of any size building if the services do not affect the structural members of the building. (c) “Residential contractor” means a contractor whose services are limited to construction, remodeling, repair, or improvement of one-family, two-family, or three-family residences not exceeding two habitable stories above no more than one uninhabitable story and accessory use structures in connection therewith. (d) “Sheet metal contractor” means a contractor whose services are unlimited in the sheet metal trade and who has the experience, knowledge, and skill necessary for the manufacture, fabrication, assembling, handling, erection, installation, dismantling, conditioning, adjustment, insulation, alteration, repair, servicing, or design, if not prohibited by law, of ferrous or nonferrous metal work of U.S. No. 10 gauge or its equivalent or lighter gauge and of other materials, including, but not limited to, fiberglass, used in lieu thereof and of air-handling systems, including the setting of air-handling equipment and reinforcement of same, the balancing of air-handling systems, and any duct cleaning and equipment sanitizing that requires at least a partial disassembling of the system. (e) “Roofing contractor” means a contractor whose services are unlimited in the roofing trade and who has the experience, knowledge, and skill to install, maintain, repair, alter, extend, or design, if not prohibited by law, and use materials and items used in the installation, maintenance, extension, and alteration of all kinds of roofing, waterproofing, and coating, except when coating is not represented to protect, repair, waterproof, stop leaks, or extend the life of the roof. The scope of work of a roofing contractor also includes skylights and any related work, required roof-deck attachments, and any repair or replacement of wood roof sheathing or fascia as needed during roof repair or replacement and any related work. (f) “Class A air-conditioning contractor” means a contractor whose services are unlimited in the execution of contracts requiring the experience, knowledge, and skill to install, maintain, repair, fabricate, alter, extend, or design, if not prohibited by law, central air-conditioning, refrigeration, heating, and ventilating systems, including duct work in connection with a complete system if such duct work is performed by the contractor as necessary to complete an air-distribution system, boiler and unfired pressure vessel systems, and all appurtenances, apparatus, or equipment used in connection therewith, and any duct cleaning and equipment sanitizing that requires at least a partial disassembling of the system; to install, maintain, repair, fabricate, alter, extend, or design, if not prohibited by law, piping, insulation of pipes, vessels and ducts, pressure and process piping, and pneumatic control piping; to replace, disconnect, or reconnect power wiring on the line or load side of the dedicated existing electrical disconnect switch on single phase electrical systems; to repair or replace power wiring, disconnects, breakers, or fuses for dedicated HVAC circuits with proper use of a circuit breaker lock; to install, disconnect, and reconnect low voltage heating, ventilating, and air-conditioning control wiring; and to install a condensate drain from an air-conditioning unit to an existing safe waste or other approved disposal other than a direct connection to a sanitary system. The scope of work for such contractor also includes any excavation work incidental thereto, but does not include any work such as liquefied petroleum or natural gas fuel lines within buildings, except for disconnecting or reconnecting changeouts of liquefied petroleum or natural gas appliances within buildings; potable water lines or connections thereto; sanitary sewer lines; swimming pool piping and filters; or electrical power wiring. A Class A air-conditioning contractor may test and evaluate central air-conditioning, refrigeration, heating, and ventilating systems, including duct work; however, a mandatory licensing requirement is not established for the performance of these specific services. (g) “Class B air-conditioning contractor” means a contractor whose services are limited to 25 tons of cooling and 500,000 Btu of heating in any one system in the execution of contracts requiring the experience, knowledge, and skill to install, maintain, repair, fabricate, alter, extend, or design, if not prohibited by law, central air-conditioning, refrigeration, heating, and ventilating systems, including duct work in connection with a complete system only to the extent such duct work is performed by the contractor as necessary to complete an air-distribution system being installed under this classification, and any duct cleaning and equipment sanitizing that requires at least a partial disassembling of the system; to install, maintain, repair, fabricate, alter, extend, or design, if not prohibited by law, piping and insulation of pipes, vessels, and ducts; to replace, disconnect, or reconnect power wiring on the line or load side of the dedicated existing electrical disconnect switch on single phase electrical systems; to repair or replace power wiring, disconnects, breakers, or fuses for dedicated HVAC circuits with proper use of a circuit breaker lock; to install, disconnect, and reconnect low voltage heating, ventilating, and air-conditioning control wiring; and to install a condensate drain from an air-conditioning unit to an existing safe waste or other approved disposal other than a direct connection to a sanitary system. The scope of work for such contractor also includes any excavation work incidental thereto, but does not include any work such as liquefied petroleum or natural gas fuel lines within buildings, except for disconnecting or reconnecting changeouts of liquefied petroleum or natural gas appliances within buildings; potable water lines or connections thereto; sanitary sewer lines; swimming pool piping and filters; or electrical power wiring. A Class B air-conditioning contractor may test and evaluate central air-conditioning, refrigeration, heating, and ventilating systems, including duct work; however, a mandatory licensing requirement is not established for the performance of these specific services. (h) “Class C air-conditioning contractor” means a contractor whose business is limited to the servicing of air-conditioning, heating, or refrigeration systems, including any duct cleaning and equipment sanitizing that requires at least a partial disassembling of the system, and whose certification or registration, issued pursuant to this part, was valid on October 1, 1988. Only a person who was registered or certified as a Class C air-conditioning contractor as of October 1, 1988, shall be so registered or certified after October 1, 1988. However, the board shall continue to license and regulate those Class C air-conditioning contractors who held Class C licenses before October 1, 1988. (i) “Mechanical contractor” means a contractor whose services are unlimited in the execution of contracts requiring the experience, knowledge, and skill to install, maintain, repair, fabricate, alter, extend, or design, if not prohibited by law, central air-conditioning, refrigeration, heating, and ventilating systems, including duct work in connection with a complete system if such duct work is performed by the contractor as necessary to complete an air-distribution system, boiler and unfired pressure vessel systems, lift station equipment and piping, and all appurtenances, apparatus, or equipment used in connection therewith, and any duct cleaning and equipment sanitizing that requires at least a partial disassembling of the system; to install, maintain, repair, fabricate, alter, extend, or design, if not prohibited by law, piping, insulation of pipes, vessels and ducts, pressure and process piping, pneumatic control piping, gasoline tanks and pump installations and piping for same, standpipes, air piping, vacuum line piping, oxygen lines, nitrous oxide piping, ink and chemical lines, fuel transmission lines, liquefied petroleum gas lines within buildings, and natural gas fuel lines within buildings; to replace, disconnect, or reconnect power wiring on the line or load side of the dedicated existing electrical disconnect switch on single phase electrical systems; to repair or replace power wiring, disconnects, breakers, or fuses for dedicated HVAC circuits with proper use of a circuit breaker lock; to install, disconnect, and reconnect low voltage heating, ventilating, and air-conditioning control wiring; and to install a condensate drain from an air-conditioning unit to an existing safe waste or other approved disposal other than a direct connection to a sanitary system. The scope of work for such contractor also includes any excavation work incidental thereto, but does not include any work such as potable water lines or connections thereto, sanitary sewer lines, swimming pool piping and filters, or electrical power wiring. A mechanical contractor may test and evaluate central air-conditioning, refrigeration, heating, and ventilating systems, including duct work; however, a mandatory licensing requirement is not established for the performance of these specific services. (j) “Commercial pool/spa contractor” means a contractor whose scope of work involves, but is not limited to, the construction, repair, and servicing of any swimming pool, or hot tub or spa, whether public, private, or otherwise, regardless of use. The scope of work includes the installation, repair, or replacement of existing equipment, any cleaning or equipment sanitizing that requires at least a partial disassembling, excluding filter changes, and the installation of new pool/spa equipment, interior finishes, the installation of package pool heaters, the installation of all perimeter piping and filter piping, and the construction of equipment rooms or housing for pool/spa equipment, and also includes the scope of work of a swimming pool/spa servicing contractor. The scope of such work does not include direct connections to a sanitary sewer system or to potable water lines. The installation, construction, modification, or replacement of equipment permanently attached to and associated with the pool or spa for the purpose of water treatment or cleaning of the pool or spa requires licensure; however, the usage of such equipment for the purposes of water treatment or cleaning does not require licensure unless the usage involves construction, modification, or replacement of such equipment. Water treatment that does not require such equipment does not require a license. In addition, a license is not required for the cleaning of the pool or spa in a way that does not affect the structural integrity of the pool or spa or its associated equipment. (k) “Residential pool/spa contractor” means a contractor whose scope of work involves, but is not limited to, the construction, repair, and servicing of a residential swimming pool, or hot tub or spa, regardless of use. The scope of work includes the installation, repair, or replacement of existing equipment, any cleaning or equipment sanitizing that requires at least a partial disassembling, excluding filter changes, and the installation of new pool/spa equipment, interior finishes, the installation of package pool heaters, the installation of all perimeter piping and filter piping, and the construction of equipment rooms or housing for pool/spa equipment, and also includes the scope of work of a swimming pool/spa servicing contractor. The scope of such work does not include direct connections to a sanitary sewer system or to potable water lines. The installation, construction, modification, or replacement of equipment permanently attached to and associated with the pool or spa for the purpose of water treatment or cleaning of the pool or spa requires licensure; however, the usage of such equipment for the purposes of water treatment or cleaning does not require licensure unless the usage involves construction, modification, or replacement of such equipment. Water treatment that does not require such equipment does not require a license. In addition, a license is not required for the cleaning of the pool or spa in a way that does not affect the structural integrity of the pool or spa or its associated equipment. (l) “Swimming pool/spa servicing contractor” means a contractor whose scope of work involves, but is not limited to, the repair and servicing of a swimming pool, or hot tub or spa, whether public or private, or otherwise, regardless of use. The scope of work includes the repair or replacement of existing equipment, any cleaning or equipment sanitizing that requires at least a partial disassembling, excluding filter changes, and the installation of new pool/spa equipment, interior refinishing, the reinstallation or addition of pool heaters, the repair or replacement of all perimeter piping and filter piping, the repair of equipment rooms or housing for pool/spa equipment, and the substantial or complete draining of a swimming pool, or hot tub or spa, for the purpose of repair or renovation. The scope of such work does not include direct connections to a sanitary sewer system or to potable water lines. The installation, construction, modification, substantial or complete disassembly, or replacement of equipment permanently attached to and associated with the pool or spa for the purpose of water treatment or cleaning of the pool or spa requires licensure; however, the usage of such equipment for the purposes of water treatment or cleaning does not require licensure unless the usage involves construction, modification, substantial or complete disassembly, or replacement of such equipment. Water treatment that does not require such equipment does not require a license. In addition, a license is not required for the cleaning of the pool or spa in a way that does not affect the structural integrity of the pool or spa or its associated equipment. (m) “Plumbing contractor” means a contractor whose services are unlimited in the plumbing trade and includes contracting business consisting of the execution of contracts requiring the experience, financial means, knowledge, and skill to install, maintain, repair, alter, extend, or, if not prohibited by law, design plumbing. A plumbing contractor may install, maintain, repair, alter, extend, or, if not prohibited by law, design the following without obtaining an additional local regulatory license, certificate, or registration: sanitary drainage or storm drainage facilities, water and sewer plants and substations, venting systems, public or private water supply systems, septic tanks, drainage and supply wells, swimming pool piping, irrigation systems, and solar heating water systems and all appurtenances, apparatus, or equipment used in connection therewith, including boilers and pressure process piping and including the installation of water, natural gas, liquefied petroleum gas and related venting, and storm and sanitary sewer lines. The scope of work of the plumbing contractor also includes the design, if not prohibited by law, and installation, maintenance, repair, alteration, or extension of air-piping, vacuum line piping, oxygen line piping, nitrous oxide piping, and all related medical gas systems; fire line standpipes and fire sprinklers if authorized by law; ink and chemical lines; fuel oil and gasoline piping and tank and pump installation, except bulk storage plants; and pneumatic control piping systems, all in a manner that complies with all plans, specifications, codes, laws, and regulations applicable. The scope of work of the plumbing contractor applies to private property and public property, including any excavation work incidental thereto, and includes the work of the specialty plumbing contractor. Such contractor shall subcontract, with a qualified contractor in the field concerned, all other work incidental to the work but which is specified as being the work of a trade other than that of a plumbing contractor. This definition does not limit the scope of work of any specialty contractor certified pursuant to s. 489.113 (6) and does not require certification or registration under this part as a category I liquefied petroleum gas dealer, or category V LP gas installer, as defined in s. 527.01 , who is licensed under chapter 527 or an authorized employee of a public natural gas utility or of a private natural gas utility regulated by the Public Service Commission when disconnecting and reconnecting water lines in the servicing or replacement of an existing water heater. A plumbing contractor may perform drain cleaning and clearing and install or repair rainwater catchment systems; however, a mandatory licensing requirement is not established for the performance of these specific services. (n) “Underground utility and excavation contractor” means a contractor whose services are limited to the construction, installation, and repair, on public or private property, whether accomplished through open excavations or through other means, including, but not limited to, directional drilling, auger boring, jacking and boring, trenchless technologies, wet and dry taps, grouting, and slip lining, of main sanitary sewer collection systems, main water distribution systems, storm sewer collection systems, and the continuation of utility lines from the main systems to a point of termination up to and including the meter location for the individual occupancy, sewer collection systems at property line on residential or single-occupancy commercial properties, or on multioccupancy properties at manhole or wye lateral extended to an invert elevation as engineered to accommodate future building sewers, water distribution systems, or storm sewer collection systems at storm sewer structures. However, an underground utility and excavation contractor may install empty underground conduits in rights-of-way, easements, platted rights-of-way in new site development, and sleeves for parking lot crossings no smaller than 2 inches in diameter if each conduit system installed is designed by a licensed professional engineer or an authorized employee of a municipality, county, or public utility and the installation of such conduit does not include installation of any conductor wiring or connection to an energized electrical system. An underground utility and excavation contractor may not install piping that is an integral part of a fire protection system as defined in s. 633.102 beginning at the point where the piping is used exclusively for such system. (o) “Solar contractor” means a contractor whose services consist of the installation, alteration, repair, maintenance, relocation, or replacement of solar panels for potable solar water heating systems, swimming pool solar heating systems, and photovoltaic systems and any appurtenances, apparatus, or equipment used in connection therewith, whether public, private, or otherwise, regardless of use. A contractor, certified or registered pursuant to this chapter, is not required to become a certified or registered solar contractor or to contract with a solar contractor in order to provide services enumerated in this paragraph that are within the scope of the services such contractors may render under this part. (p) “Pollutant storage systems contractor” means a contractor whose services are limited to, and who has the experience, knowledge, and skill to install, maintain, repair, alter, extend, or design, if not prohibited by law, and use materials and items used in the installation, maintenance, extension, and alteration of, pollutant storage tanks. Any person installing a pollutant storage tank shall perform such installation in accordance with the standards adopted pursuant to s. 376.303 . (q) “Specialty contractor” means a contractor whose scope of work and responsibility is limited to a particular phase of construction established in a category adopted by board rule and whose scope is limited to a subset of the activities described in one of the paragraphs of this subsection. (4) “Primary qualifying agent” means a person who possesses the requisite skill, knowledge, and experience, and has the responsibility, to supervise, direct, manage, and control the contracting activities of the business organization with which he or she is connected; who has the responsibility to supervise, direct, manage, and control construction activities on a job for which he or she has obtained the building permit; and whose technical and personal qualifications have been determined by investigation and examination as provided in this part, as attested by the department. (5) “Secondary qualifying agent” means a person who possesses the requisite skill, knowledge, and experience, and has the responsibility to supervise, direct, manage, and control construction activities on a job for which he or she has obtained a permit, and whose technical and personal qualifications have been determined by investigation and examination as provided in this part, as attested by the department. (6) “Contracting” means, except as exempted in this part, engaging in business as a contractor and includes, but is not limited to, performance of any of the acts as set forth in subsection (3) which define types of contractors. The attempted sale of contracting services and the negotiation or bid for a contract on these services also constitutes contracting. If the services offered require licensure or agent qualification, the offering, negotiation for a bid, or attempted sale of these services requires the corresponding licensure. However, the term “contracting” shall not extend to an individual, partnership, corporation, trust, or other legal entity that offers to sell or sells completed residences on property on which the individual or business entity has any legal or equitable interest, or to the individual or business entity that offers to sell or sells manufactured or factory-built buildings that will be completed on site on property on which either party to a contract has any legal or equitable interest, if the services of a qualified contractor certified or registered pursuant to the requirements of this chapter have been or will be retained for the purpose of constructing or completing such residences. (7) “Certificate” means a certificate of competency issued by the department as provided in this part. (8) “Certified contractor” means any contractor who possesses a certificate of competency issued by the department and who shall be allowed to contract in any jurisdiction in the state without being required to fulfill the competency requirements of that jurisdiction. (9) “Registration” means registration with the department as provided in this part. (10) “Registered contractor” means any contractor who has registered with the department pursuant to fulfilling the competency requirements in the jurisdiction for which the registration is issued. Registered contractors may contract only in such jurisdictions. (11) “Certification” means the act of obtaining or holding a certificate of competency from the department as provided in this part. (12) “Local construction regulation board” means a board, composed of not fewer than three residents of a county or municipality, which the governing body of that county or municipality may create and appoint to maintain the proper standard of construction of that county or municipality. (13) “Business organization” means any partnership, corporation, business trust, joint venture, or other legal entity which engages or offers to engage in the business of contracting or acts as a contractor as defined in this section. (14) “Financially responsible officer” means a person other than the primary qualifying agent who with the approval of the board assumes personal responsibility for all financial aspects of the business organization. (15) “Structural component” means any vertical or horizontal load-bearing member of a structure which supports dead or live loads in addition to its own weight and includes, but is not limited to, a foundation, an exterior or interior load-bearing wall, a column, a column beam, a floor, and a roof structure. (16) “Arbitration” means a process whereby a neutral third person or panel, called an arbitrator or arbitration panel, considers the facts and arguments presented by the parties and renders a decision which is binding on the parties. (17) “Pollutant storage tank” means a tank, together with associated piping or dispensing facilities, which is or could be used for the storage or supply of pollutants as defined in s. 376.301 and which is required to be registered under chapter 17-761, Florida Administrative Code. (18) “Tank” means any container other than one which is aboveground and either elevated or situated upon an impermeable surface, or which is located in an accessible underground area and either elevated or situated upon an impermeable surface therein, in such manner that any leak in such container may be readily detected. (19) “Initial issuance” means the first time a certificate or registration is granted to an individual or business organization, including the first time an individual becomes a qualifying agent for that business organization and the first time a business organization is qualified by that individual.

489.103 Exemptions. — This part does not apply to: (1) Contractors in work on bridges, roads, streets, highways, or railroads, and services incidental thereto. The board, in agreement with the Department of Transportation, shall, by rule, define “services incidental thereto” for the purposes of this subsection only. (2) Any employee of a certificateholder or registrant who is acting within the scope of the license held by that certificateholder or registrant and with the knowledge and permission of the licenseholder. However: (a) If the employer is not a certificateholder or registrant in that type of contracting, and the employee performs any of the following, the employee is not exempt: 1. Holds himself or herself or his or her employer out to be licensed or qualified by a licensee; 2. Leads the consumer to believe that the employee has an ownership or management interest in the company; or 3. Performs any of the acts which constitute contracting. (b) The legislative intent of this subsection is to place equal responsibility on the unlicensed business and its employees for the protection of the consumers in contracting transactions. For the purpose of this part, “employee” is defined as a person who receives compensation from and is under the supervision and control of an employer who regularly deducts the F.I.C.A. and withholding tax and provides workers’ compensation, all as prescribed by law. (3) An authorized employee of the United States, this state, or any municipality, county, irrigation district, reclamation district, or any other municipal or political subdivision, except school boards, state university boards of trustees, and community college boards of trustees, unless for the purpose of performing routine maintenance or repair or construction not exceeding $200,000 to existing installations, if the employee does not hold himself or herself out for hire or otherwise engage in contracting except in accordance with his or her employment. If the construction, remodeling, or improvement exceeds $200,000, school boards, state university boards of trustees, and community college boards of trustees shall not divide the project into separate components for the purpose of evading this section. (4) An officer appointed by a court when he or she is acting within the scope of his or her office as defined by law or court order. When construction projects which were not underway at the time of appointment of the officer are undertaken, the officer shall employ or contract with a licensee. (5) Public utilities, including municipal gas utilities and special gas districts as defined in chapter 189, telecommunications companies as defined in s. 364.02 (13), and natural gas transmission companies as defined in s. 368.103 (4), on construction, maintenance, and development work performed by their employees. (6) The sale or installation of any finished products, materials, or articles of merchandise that are not fabricated into and do not become a permanent fixed part of the structure, such as awnings. However, this subsection does not exempt in-ground spas and swimming pools that involve excavation, plumbing, chemicals, or wiring of any appliance without a factory-installed electrical cord and plug. This subsection does not limit the exemptions provided in subsection (7). (7)(a) Owners of property when acting as their own contractor and providing direct, onsite supervision themselves of all work not performed by licensed contractors: 1. When building or improving farm outbuildings or one-family or two-family residences on such property for the occupancy or use of such owners and not offered for sale or lease, or building or improving commercial buildings, at a cost not to exceed $75,000, on such property for the occupancy or use of such owners and not offered for sale or lease. In an action brought under this part, proof of the sale or lease, or offering for sale or lease, of any such structure by the owner-builder within 1 year after completion of same creates a presumption that the construction was undertaken for purposes of sale or lease. 2. When repairing or replacing wood shakes or asphalt or fiberglass shingles on one-family, two-family, or three-family residences for the occupancy or use of such owner or tenant of the owner and not offered for sale within 1 year after completion of the work and when the property has been damaged by natural causes from an event recognized as an emergency situation designated by executive order issued by the Governor declaring the existence of a state of emergency as a result and consequence of a serious threat posed to the public health, safety, and property in this state. 3. When installing, uninstalling, or replacing solar panels on one-family, two-family, or three-family residences, and the local permitting agency’s county or municipal government is participating in a “United States Department of Energy SunShot Initiative: Rooftop Solar Challenge” grant. However, an owner must utilize a licensed electrical contractor to effectuate the wiring of the solar panels, including any interconnection to the customer’s residential electrical wiring. The limitations of this exemption shall be expressly stated in the building permit approved and issued by the permitting agency for such project. 4. When completing the requirements of a building permit, where the contractor listed on the permit substantially completed the project as determined by the local permitting agency, for a one-family or two-family residence, townhome, or an accessory structure of a one-family or two-family residence or townhome or an individual residential condominium unit or cooperative unit. Prior to qualifying for the exemption, the owner must receive approval from the local permitting agency, and the local permitting agency must determine that the contractor listed on the permit substantially completed the project. An owner who qualifies for the exemption under this subparagraph is not required to occupy the dwelling or unit for at least 1 year after the completion of the project. (b) This subsection does not exempt any person who is employed by or has a contract with such owner and who acts in the capacity of a contractor. The owner may not delegate the owner’s responsibility to directly supervise all work to any other person unless that person is registered or certified under this part and the work being performed is within the scope of that person’s license. For the purposes of this subsection, the term “owners of property” includes the owner of a mobile home situated on a leased lot. (c) To qualify for exemption under this subsection, an owner must personally appear and sign the building permit application and must satisfy local permitting agency requirements, if any, proving that the owner has a complete understanding of the owner’s obligations under the law as specified in the disclosure statement in this section. However, for purposes of implementing a “United States Department of Energy SunShot Initiative: Rooftop Solar Challenge” grant and the participation of county and municipal governments, including local permitting agencies under the jurisdiction of such county and municipal governments, an owner’s notarized signature or personal appearance to sign the permit application is not required for a solar project, as described in subparagraph (a)3., if the building permit application is submitted electronically to the permitting agency and the owner certifies the application and disclosure statement using the permitting agency’s electronic confirmation system. If any person violates the requirements of this subsection, the local permitting agency shall withhold final approval, revoke the permit, or pursue any action or remedy for unlicensed activity against the owner and any person performing work that requires licensure under the permit issued. The local permitting agency shall provide the person with a disclosure statement in substantially the following form: DISCLOSURE STATEMENT 1. I understand that state law requires construction to be done by a licensed contractor and have applied for an owner-builder permit under an exemption from the law. The exemption specifies that I, as the owner of the property listed, may act as my own contractor with certain restrictions even though I do not have a license. 2. I understand that building permits are not required to be signed by a property owner unless he or she is responsible for the construction and is not hiring a licensed contractor to assume responsibility. 3. I understand that, as an owner-builder, I am the responsible party of record on a permit. I understand that I may protect myself from potential financial risk by hiring a licensed contractor and having the permit filed in his or her name instead of my own name. I also understand that a contractor is required by law to be licensed in Florida and to list his or her license numbers on permits and contracts. 4. I understand that I may build or improve a one-family or two-family residence or a farm outbuilding. I may also build or improve a commercial building if the costs do not exceed $75,000. The building or residence must be for my own use or occupancy. It may not be built or substantially improved for sale or lease, unless I am completing the requirements of a building permit where the contractor listed on the permit substantially completed the project. If a building or residence that I have built or substantially improved myself is sold or leased within 1 year after the construction is complete, the law will presume that I built or substantially improved it for sale or lease, which violates the exemption. 5. I understand that, as the owner-builder, I must provide direct, onsite supervision of the construction. 6. I understand that I may not hire an unlicensed person to act as my contractor or to supervise persons working on my building or residence. It is my responsibility to ensure that the persons whom I employ have the licenses required by law and by county or municipal ordinance. 7. I understand that it is a frequent practice of unlicensed persons to have the property owner obtain an owner-builder permit that erroneously implies that the property owner is providing his or her own labor and materials. I, as an owner-builder, may be held liable and subjected to serious financial risk for any injuries sustained by an unlicensed person or his or her employees while working on my property. My homeowner’s insurance may not provide coverage for those injuries. I am willfully acting as an owner-builder and am aware of the limits of my insurance coverage for injuries to workers on my property. 8. I understand that I may not delegate the responsibility for supervising work to a licensed contractor who is not licensed to perform the work being done. Any person working on my building who is not licensed must work under my direct supervision and must be employed by me, which means that I must comply with laws requiring the withholding of federal income tax and social security contributions under the Federal Insurance Contributions Act (FICA) and must provide workers’ compensation for the employee. I understand that my failure to follow these laws may subject me to serious financial risk. 9. I agree that, as the party legally and financially responsible for this proposed construction activity, I will abide by all applicable laws and requirements that govern owner-builders as well as employers. I also understand that the construction must comply with all applicable laws, ordinances, building codes, and zoning regulations. 10. I understand that I may obtain more information regarding my obligations as an employer from the Internal Revenue Service, the United States Small Business Administration, the Florida Department of Financial Services, and the Florida Department of Revenue. I also understand that I may contact the Florida Construction Industry Licensing Board at (telephone number) or (Internet website address) for more information about licensed contractors. 11. I am aware of, and consent to, an owner-builder building permit applied for in my name and understand that I am the party legally and financially responsible for the proposed construction activity at the following address: (address of property) . 12. I agree to notify (issuer of disclosure statements) immediately of any additions, deletions, or changes to any of the information that I have provided on this disclosure. Licensed contractors are regulated by laws designed to protect the public. If you contract with a person who does not have a license, the Construction Industry Licensing Board and Department of Business and Professional Regulation may be unable to assist you with any financial loss that you sustain as a result of a complaint. Your only remedy against an unlicensed contractor may be in civil court. It is also important for you to understand that, if an unlicensed contractor or employee of an individual or firm is injured while working on your property, you may be held liable for damages. If you obtain an owner-builder permit and wish to hire a licensed contractor, you will be responsible for verifying whether the contractor is properly licensed and the status of the contractor’s workers’ compensation coverage. Before a building permit can be issued, this disclosure statement must be completed and signed by the property owner and returned to the local permitting agency responsible for issuing the permit. A copy of the property owner’s driver license, the notarized signature of the property owner, or other type of verification acceptable to the local permitting agency is required when the permit is issued. Signature: (signature of property owner) . Date: (date) . (d) A building permit application and disclosure statement electronically submitted by an owner to the authority for a solar project, as described in subparagraph (a)3., must also contain the following additional statement: OWNER’S ELECTRONIC SUBMISSION STATEMENT: Under penalty of perjury, I declare that all the information contained in this building permit application and the representations made in the required disclosure statement are true and correct. (e) A permitting authority that accepts a building permit application and disclosure statement in an electronic format from an owner who is exempt pursuant to this subsection and who applies for a permit relating to a solar project, as described in subparagraph (a)3., is not liable in any civil action for inaccurate information submitted by the owner using the authority’s electronic confirmation system. (8) Any construction, alteration, improvement, or repair carried on within the limits of any site the title to which is in the United States or with respect to which federal law supersedes this part. (9) Any work or operation of a casual, minor, or inconsequential nature in which the aggregate contract price for labor, materials, and all other items is less than $2,500, but this exemption does not apply: (a) If the construction, repair, remodeling, or improvement is a part of a larger or major operation, whether undertaken by the same or a different contractor, or in which a division of the operation is made in contracts of amounts less than $2,500 for the purpose of evading this part or otherwise. (b) To a person who advertises that he or she is a contractor or otherwise represents that he or she is qualified to engage in contracting. (10)(a) Any construction or operation incidental to the construction or repair of irrigation and drainage ditches; (b) Regularly constituted irrigation districts or reclamation districts; or (c) Clearing or other work on the land in rural districts for fire prevention purposes or otherwise except when performed by a licensee. (11) A registered architect or engineer acting within the scope of his or her practice or any person exempted by the law regulating architects and engineers, including persons doing design work as specified in s. 481.229 (1)(b); provided, however, that an architect or engineer shall not act as a contractor unless properly licensed under this chapter. (12) Any person who only furnishes materials or supplies without fabricating them into, or consuming them in the performance of, the work of the contractor. (13) Any person who is licensed pursuant to chapter 527 when such person is performing the work authorized by such license. (14) Any person who sells, services, or installs heating or air-conditioning units which have a capacity no greater than 3 tons or 36,000 Btu, which have no ducts, and which have a factory-installed electrical cord and plug. (15) The installation and maintenance of water conditioning units for domestic, commercial, or industrial purposes by operators of water conditioning services. No municipality or county may adopt an ordinance, rule, or regulation which requires such an operator to become licensed, certified, or registered as a plumber or which otherwise prevents the installation and maintenance of such water conditioning units by an operator. (16) An architect or landscape architect licensed pursuant to chapter 481 or an engineer licensed pursuant to chapter 471 who offers or renders design-build services which may require the services of a contractor certified or registered pursuant to the provisions of this chapter, as long as the contractor services to be performed under the terms of the design-build contract are offered and rendered by a certified or registered general contractor in accordance with this chapter. (17) Contracting for repair, maintenance, remodeling, or improvement by any person licensed under part I of chapter 475 while acting as the owner’s agent pursuant to that license, where all work requiring a contractor is performed by a contractor who has a current, valid certificate or registration issued under this part to perform such work, and where the aggregate contract for labor, materials, and all other items is less than $5,000; however, this exemption does not apply: (a) If the maintenance, repair, remodeling, or improvement is a part of a larger or major operation, whether undertaken by the same or a different contractor, or in which a division of the operation is made in contracts of amounts less than $5,000 for the purpose of evading this part or otherwise. (b) To a person who advertises that he or she is qualified to engage in contracting. (18) Any one-family, two-family, or three-family residence constructed or rehabilitated by Habitat for Humanity International, Inc., or its local affiliates. Habitat for Humanity International, Inc., or its local affiliates, must: (a) Obtain all necessary building permits. (b) Obtain all required building code inspections. (c) Provide for supervision of all work by an individual with construction experience. (19) A disaster recovery mitigation organization or a not-for-profit organization repairing or replacing a one-family, two-family, or three-family residence that has been impacted by a disaster when such organization: (a) Is using volunteer labor to assist the owner of such residence in mitigating unsafe living conditions at the residence; (b) Is not holding itself out to be a contractor; (c) Obtains all required building permits; (d) Obtains all required building code inspections; and (e) Provides for the supervision of all work by an individual with construction experience. (20) The sale, delivery, assembly, or tie-down of prefabricated portable sheds that are not more than 250 square feet in interior size and are not intended for use as a residence or as living quarters. This exemption may not be construed to interfere with the Florida Building Code or any applicable local technical amendment to the Florida Building Code, local licensure requirements, or other local ordinance provisions. (21) The sale, delivery, assembly, or tie-down of lawn storage buildings and storage buildings not exceeding 400 square feet and bearing the insignia of approval from the department showing compliance with the Florida Building Code. (22) A person licensed pursuant to s. 633.304 (1)(d) or (3)(b) performing work authorized by such license. (23) An employee of an apartment community or apartment community management company who makes minor repairs to existing electric water heaters or to existing electric heating, ventilating, and air-conditioning systems if: (a) The employee: 1. Does not hold himself or herself or his or her employer out to be licensed or qualified by a licensee. 2. Does not perform any acts, other than acts authorized by this subsection, that constitute contracting. 3. Receives compensation from and is under the supervision and control of an employer who deducts the FICA and withholding tax and who provides workers’ compensation, as prescribed by law. 4. Holds a current certificate for apartment maintenance technicians issued by the National Apartment Association and accredited by the American National Standards Institute. Requirements for obtaining such certificate must include at least: a. One year of apartment or rental housing maintenance experience. b. Successful completion of at least 90 hours of courses or online content that covers electrical maintenance and repair; plumbing maintenance and repair; heating, ventilating, or air-conditioning system maintenance and repair; appliance maintenance and repair; and interior and exterior maintenance and repair. c. Completion of all examination requirements. (b) The equipment: 1. Is already installed on the property owned by the apartment community or managed by the apartment community management company. 2. Is not being modified except to replace components necessary to return the equipment to its original condition and the partial disassembly associated with the replacement. 3. Is a type of equipment commonly installed in similar locations. 4. Is repaired with new parts that are functionally identical to the parts being replaced. (c) An individual repair does not involve replacement parts that cost more than $1,000. An individual repair may not be so extensive as to be a functional replacement of the electric water heater or the existing electric heating, ventilating, or air-conditioning system being repaired. For purposes of this paragraph, an individual repair may not be part of a larger or major project that is divided into parts to avoid this restriction. (d) The property owned by the apartment community or managed by the apartment community management company includes at least 100 apartments. This subsection does not limit the authority of a municipality or county to adopt or enforce an ordinance, rule, or regulation requiring licensure, certification, or registration of a person employed as an apartment maintenance technician or apartment repair worker or in any position that includes any part of the scope of work described in this subsection. (24) A member of the Miccosukee Tribe of Indians of Florida or the Seminole Tribe of Florida when constructing chickees as described in s. 553.73 (10)(i).